Bird feeders have long become something more than just a device for feeding them. We admit that we not only want to make life easier for birds, but also to observe the behavior of wonderful birds, decorate our yard, realize ourselves in front of others and teach our children to love this world. If at the same time our wards help in protecting the garden from pests, it will turn out very well.

Bird feeders: what should they be?

When starting to make a feeder, it is useful to remember Exupery’s remark: we are responsible for those we have tamed.

In other words, having accustomed the birds to easy food production, we are obliged to think about them all winter.

Otherwise, they will experience big problems, losing food overnight, and may even die. Now we list a number of characteristics that a poultry canteen must meet:

• the bird table must have sides that will prevent the wind from blowing away the food;
• the craft should not have sharp edges that could injure birds’ legs;
• a roof over the table will protect food from rain and snow;
• the feeder should be, if possible, inaccessible to cats;
• the holes in the walls of the craft must be of sufficient size so that the birds are not afraid of closed spaces;
• the product must be moisture resistant in order to last at least one season;
• the craft should not sway too much in the wind, that is, it is better to weigh it down with a piece of linoleum or pebbles.

Bird feeders: what are they?

There are so many people who want to make an exclusive table for birds that they have created an innumerable number of hand-made works. Obviously, everyone's preferences and capabilities are different. We intend to offer you a range of different products with a description of their features and designs. Of course, we will also discuss the wishes of the birds themselves. Putting everything together, you will have the opportunity to compose your own “symphony” called “bird feeder”.

Made of wood - most options

The picture shows feeders made from planks. Depending on preferences and availability of material, you can choose one or another design. The very first option has a twist: a gap on the side bar for water to drain. Any product will last longer if it is treated with impregnation, painted and varnished.

These products are a little more complicated - they are all made of bars and slats. This material allows you to make quite interesting and exclusive options. Pieces of roofing felt on the roof will significantly increase the durability of the craft. The bars and slats can be secured with small nails or glue.

Using tree branches will bring your craft closer to nature. The product can be quite simple and unusual. The use of impregnation and varnish is also advisable in this case.

Feeders made from birch branches look very interesting. Given such material, I would choose this option. Various roof construction methods are possible. Birch bark already has protective functions, but varnish will not hurt.

The photo shows several feeders for mounting on a wall or to a tree trunk. They all have a back plate with a hole for fastening. You can independently make options of varying complexity. The glass jar feeder is very simple and easy to use.

The photo shows surprisingly simple and original wood structures. It’s quite possible to make such feeders yourself. Treatment with protective impregnation did them good.

Carved products are fraught with considerable possibilities. However, in this case it is difficult to do without a jigsaw. A piece of galvanized steel on the roof is correct. Processing with a blowtorch will give the product a special color. It is simply necessary to protect a product on which a lot of time has been spent from moisture.

The images above show a selection of products made by professionals. All parts of the feeders were first processed and painted, and then assembled into a single structure. As a result, we have impeccable appearance and durability. Nothing prevents you from repeating the same thing!

The photo shows feeders that will decorate a mansion of any level with their presence. Probably, such products are made by specialists in a workshop. I am sure that if you set a goal, it is quite possible to repeat the elite version yourself.

In the photo above we have selected the most interesting ideas for wood feeders. They differ in materials and design. Moreover, it is quite possible to make such products yourself.

Made from plywood – its features and capabilities

Here are several designs of plywood feeders. There are quite a lot of products made using this technology. The parts of such feeders are cut out on a machine and sold in stores as sets. Crafts are assembled easily and quickly. A set from the store is interesting and useful to process and paint to your taste.

These products are made in a workshop from thick plywood. The designs are assembled from simple parts and can be easily replicated yourself if you have a jigsaw. Clean plywood clearly requires coating and decoration.

It is much easier to make a plywood feeder using bars and slats. In this case, you can do without a jigsaw. The designs shown in the picture are different, but simple.

Plywood feeders using wood are quite popular. We demonstrate several more possible options. Simplicity of execution cannot create barriers to exclusive options if creative people get down to business.

The picture above shows evidence of the effectiveness of using paints in making a feeder. In the hands of craftsmen, fairly simple products can easily turn into fabulous attributes. In this case, desire is more important than the inclinations of an artist.

Especially for those who want to make a feeder from plywood and blocks, we have prepared product drawings. All parts are numbered for convenience. To assemble the feeder you will need 4mm thick plywood, a block with a cross section of 20x20mm and wood screws.

Here is a drawing of the parts of the feeder. The number of the latter is given in the table. The cross-section of the 20X20 bar is not shown in the drawing.

From bottles - simple and reliable

Very often bird feeders are made from plastic bottles. This is due to the availability and durability of available materials and ease of manufacture. Transparent plastic bottles allow you to easily observe the behavior of birds.

The sharp edges of the plastic must be treated with electrical tape or a PVC tube cut along the length. Then the birds will not injure their legs and plumage. Light bottle feeders should be weighted with pieces of linoleum or pebbles to prevent them from swaying in the wind. The image above shows the simplest options.

Containers made from automobile fluids make it possible to obtain more reliable and voluminous structures. Unfortunately, they are not transparent. In feeders made from any plastic containers, small holes should be made in the bottom to allow water to drain.

Five-liter eggplants can be decorated beyond recognition. Burlap, twine, washcloth and small twigs will do. To prevent beauty from fading quickly, it is necessary to use moisture-resistant materials and glue.

As you can see, there are plenty of options for decorating feeders made from five-liter bottles. Show your imagination and make it your own and unique. Don't forget about the reliability of the design.

In the photo above there are several more typical techniques for using plastic bottles:

1. In the first picture, two holes were made in the bottle opposite each other, closer to the neck. A stick was inserted into the holes - a stick. A hole for food was made just below the perch. It should have optimal dimensions: the seeds do not spill, but are accessible to the bird. Then they poured in the food, turned the container upside down and secured it to the tree.
2. In the next image, the role of dispensers and shelves is played by the two upper parts of the bottles, tightly inserted with their necks into the holes on the sides of the main bottle. The lower edges of the specified parts are bent and turned inward so that the birds do not injure their paws.
3. The picture on the left below shows the possibilities of using paints. The simple, tasteful design brings the technical transparency of plastic to life.
4. The presence of wooden spoons helps to call the birds for dinner. They are simply threaded through the holes in the bottle. It is better to place the spoons at an angle so that two birds can eat at once. The holes for food above the spoon should not be too large so that the food does not spill out all at once.

Made from cardboard and bags - cheap and cheerful

Bird feeders made of cardboard and cardboard boxes are the most unreliable. But you can make a large feeder and decorate it as you wish. You can increase the service life of a cardboard bird canteen by covering it with tape or film.

Dairy and juice bags are a good way to make feeders. They cost nothing and have good moisture resistance. Of course, bottles are more durable, but bags are easier to work with. You have several options for execution.

We decided to make a fun and simple feeder from a 2 liter juice carton. The idea came up to feed the birds on a makeshift bus. The master class on assembling the craft is quite simple:

Unusual – bunker, transparent, designer, funny

Of particular interest to us are bunker feeders, which provide automatic feed supply as it is consumed. This way, bird food is not blown away by the wind, and we do not have to constantly monitor the availability of grain. The design of such a feeder can be very different, but the essence is the same: through a hole of a certain size, food pours in from above and replenishes the bird’s table.

In the above examples, the dispenser is:

• gap between two glasses;
• narrow neck of a glass bottle;
• holes at the bottom of the plastic bottle.

We have already considered similar options in the description of feeders made from plastic bottles. Based on these principles, you can certainly come up with something new.

Feeders using plexiglass look elegant. Birds and food are clearly visible. The design approach makes you want to repeat a successful experiment.

I don't want to throw away the rest of the tea set. Here are four options for using dishes as a feeder. The moisture resistance and appearance of the material are beyond doubt. Securing a cup or teapot in the garden is not difficult.

Particularly persistent and talented home-made people create funny feeders - jokes. We must be determined to repeat the best examples. It’s especially nice to compose something of your own.

To begin with, you can try a simpler option made from plastic bottles. Much depends on the materials you have at hand. The above examples are quite subject to female hands.

Here are four options for a “male” cool wooden feeder. The design of the crafts is quite obvious. Repeating the proposed ideas is a very real task.

Here are images of several more options for unusual bird feeders. The main idea is obvious: don't be afraid to experiment. It’s easier not to torment yourself with searching for exactly the same materials, but to use existing ones.

Let's make a feeder together - a snowman from a plastic bottle

Of course, I want to make a bird feeder simpler and more interesting. It seems to us that a snowman with gifts from Santa Claus for the birds is a suitable option. The master class for making crafts is as follows:

1. On one side of the bottle we mark the snowman's mouth with a marker. Now this wall will be the face. We cut out the outlines of the mouth according to the markings. Bend the resulting tongue down 90 degrees.
2. On the side we mark the ear in the form of an inclined oval, narrowed at the bottom. Cut a hole simulating an ear.
   
   
3. Place the resulting piece of plastic on the other side and outline it with a marker. Cut out the second ear.
4. Mark a large rectangular hole at the back of the head and cut it out.
   
   
5. The result was a blank, as in the photo above.
6. Paint the snowman's cap the same blue as the bottle cap. Paint the bottom of the eggplant with white paint.
   
   
7. We paint the tongue with red paint.
   
   
8. We put a plastic corrugated tube with a diameter of 16mm on the edges of all holes. In an electrical goods store, 2m of such pipe will cost absolutely nothing. We first cut the tube along its entire length.
9. To weight the container we use linoleum. Place the container on it and trace it with a marker. It is better to cut out two such parts.
   
   
10. We prepare plugs, screws, a sealant cover and a stick in accordance with the picture. We make holes in the corks for screws. We make a hole in the red cork for the stick.
    
    
11. We make two holes to install the nose stick. We punch one at the place of the nose, the other at the back of the head. We insert a stick into them. We first put the red plug on it, and then the sealant cover. The result is a snowman's nose.
    
    
12. We collect the eyes from small white and large blue caps. We screw them into place with self-tapping screws. From the inside, we screw two more covers onto the protruding screws to securely fasten the eyes and protect against sharp screws. All is ready!

Master class on making a classic feeder

At school, my youngest son was encouraged to make a bird feeder. The following materials were found:

• painted galvanized corner 50x50mm;
• wooden slats with a cross section of 20x40mm;
• a piece of plywood 4mm thick.

From which it was decided to compose my work. The sequence of the master class is as follows:

Cereal biscuits for birds

Sometimes you can do without creating a feeder to help the birds. You can hang special bird cookies on tree branches. Note that bird cookies made from grains look so tempting that I would eat them myself.

The first way to make a delicacy is as follows:

• prepare molds for making cookies;
• place pieces of twine in the molds that will serve as pendants;
• dissolve the gelatin packet in warm water;
• pour grain feed into the prepared solution;
• pour the mixture into the prepared molds;
• place the food in the refrigerator to harden;
• We hang the finished cookies on tree branches: accessible to our eyes and out of reach of cats.

In the absence of forms, beautiful food for birds can be made in another way:

• cut out figures of various shapes from cardboard;
• we make holes in the cardboard blanks, thread twine through them and tie rings for fastening on the tree;
• to attach the food to the cardboard, we prepare special glue, which consists of an egg, a spoonful of honey, 2 tablespoons of oatmeal and flour;
• mix the mixture and leave to mature for half an hour;
• When the glue is ready, lubricate the cardboards with it and roll the latter in bird food;
• send the semi-finished product to the refrigerator to harden;
• When the cookies are ready, we hang them on the tree and go to the window to observe.

Bird food: “what is good and what is bad”?

Take a close look at the birds that have remained to spend the winter in our area. The hope was frozen in their eyes that we would not give them an “expired product” or harmful food for them, from which the birds would suffer. Let's remember what we cannot treat our charges to, what should never be included in their diet:

• salted and fried seeds;
• cream puffs and cake;
• fresh white bread;
• Rye bread;
• nuts;
• chips;
• cereals;
• leftover bananas and other citrus fruits;
• fresh fruits.

Fortunately, the range of possibilities is much wider. Birds can be offered:

• bread crumbs;
• sunflower, pumpkin and watermelon seeds;
• cereals: oats, wheat, millet, barley;
• rice, buckwheat;
• unsalted lard especially for tits;
• viburnum and rowan, maple and ash seeds especially for bullfinches.

Eggshells, coarse sand, and crushed chalk will serve as seasoning for birds' dinner, especially during the nest-building period. Thus, we know almost everything about bird feeders and bird food. By the way, observing the behavior of birds in spring and summer is no less fascinating than in winter. We wish you good luck and offer a video to help.

For birds, you need to have a few simple items and tools.

You can make a feeding trough with your children, but keep in mind that you need to watch every step, since during the construction process sharp things are used - scissors, knives, screwdrivers and even, sometimes, a saw.

There are many options for feeders - made from plywood, plastic bottles, tin cans or cardboard.

Here are the most interesting, popular and original ideas for creating a feeder:

Feeder made from scrap materials: toilet paper rolls

You will need:

1 toilet paper roll

Peanut butter

Small bowl

Plate

A couple of branches

Strong thread or fishing line

Knife (dull or plastic).

1. Connect two branches or sticks together using hot glue or string. You can skip this point if you make 4 holes in the sleeve (see below).

2. Make holes in the toilet paper roll so that you can thread two branches or sticks through them. It is better to make 2 holes: a little higher and 2 slightly lower (see image). This item is not required, because The sleeve can be put on differently.

3. Place the peanut butter in a small bowl and use a plastic knife to spread the butter onto the surface of the cardboard toilet paper roll.

4. Sprinkle the food over the peanut butter sleeve.

5. Repeat steps 3 and 4 for 4 more bushings.

6. Tie a strong thread to the connected branches so that the structure can be hung.

7. Hang all the cardboard tubes on the branch structure, and then hang everything on the tree.

Feeder made from a plastic bottle. Option 1.

You will need:

Any plastic bottle

Ribbon, thread or fishing line

Awl or drill (for making holes in the bottle and plastic cap)

Bolt and nut

Stationery or simple knife (if necessary)

Deep plastic plate.

1. Prepare a plastic bottle. Remove the label from it, wash it well and dry it.

2. Make a hole in the middle of the lid and plastic plate.

3. Attach the lid to the plate using a bolt and nut.

4. Make a hole in the bottom of the bottle (bottom).

5. Make several holes on the side (4-5), near the neck of the bottle, so that the food can spill out when you turn the bottle over. Holes can be made with a stationery knife if the bottle is not too dense.

6. Take the ribbon, fold it in half, and tie the ends in a knot. Thread the ribbon through the hole at the bottom of the bottle.

Now you can pour food into the bottle, screw on the cap and turn it over. The ribbon will allow you to hang the feeder on a branch.

Bird feeder made from a plastic bottle. Option 2.

You will need:

Plastic bottle

Plastic container

Strong thread or fishing line

Screwdriver or nail

Knife (simple or stationery).

1. Remove the cap from the bottle and the cap from the container.

2. Place the bottle cap on the container cap (in the center) and trace with a pen, felt-tip pen or pencil.

3. Using a utility knife, cut a hole in the lid of the container. The hole can be made slightly smaller than the diameter of the bottle cap.

4. Make one hole along the edges of the container lid.

5. Make a hole in the center of the bottle cap. The hole should be large enough to allow bird food to spill out.

6. Place the cap on the bottle and then insert the bottle into the hole in the container cap.

7. Tie a strong thread to the bottle and put the cap on the container.

Now you can pour food into the bottle or pour water and hang the feeder on a tree.

How to make a feeder from a box (photo instructions)

Original polymer clay feeder

You will need:

Polymer clay

Rope

Thick wire or piece of aluminum

Baking bowl or any other utensil that can be placed in the oven

A small piece of fabric.

1. First roll out the clay on a flat surface until it is about 6mm thick.

2. Carefully place the rolled out clay inside the baking bowl. Trim off any excess pieces so that the clay lies flat. Make 3 large holes in the clay for the rope.

3. Place the bowl of clay in the oven. Read the clay instructions carefully to know how long it takes for the clay to harden in the oven.

4. When the clay has hardened, carefully remove it from the bowl, tie three pieces of rope to it - tie a knot at one end of each rope, and insert the other end into the hole of the clay plate.

5. Tie all ends of the rope and secure them with wire.

6. It is advisable to place a small piece of fabric inside the plate so that the birds do not accidentally peck the clay along with the food.

Original do-it-yourself pumpkin feeder

You will need:

Small pumpkin

Wooden crossbars (even branches can be used)

Thin wire.

1. You need to cut off the top of the pumpkin.

2. Using a knife or screwdriver, make 4 holes in the pumpkin to insert branches or wooden slats into. Make 2 opposite holes at the same height and two other opposite ones slightly lower - this way you will have one branch slightly higher than the other.

3. Take a thin wire and wrap it around each end of the branches so that the feeder can be hung on the tree. Connect all the ends of the wire so that the feeder can hang evenly. Twist them into a hook.

Original DIY bird feeder idea

This feeder is suitable for sub-zero temperatures.

You will need:

Large plastic bottle

Small plastic bottle or small plastic container

Scissors

Coniferous branches

Berries (optional)

Seeds

1. Cut off the bottom of a large and small plastic bottle. First you can make a hole with a knife and then cut with scissors. You will have the base of the feeder.

2. Place spruce branches, berries and seeds in a circle in the cut-out bottom of a large bottle.

3. Place the bottom of a small bottle or small plastic container in the center of the base.

4. Pour earth, sand or pebbles into a small container.

5. Tie strong threads or fishing line to the feeder so it can be hung.

6. If you put the feeder in the freezer overnight, and then take out and remove the plastic parts, you will get an ice feeder.

How to make a feeder with your own hands using a bottle

You will need:

Small glass or plastic bottle (preferably with a cap)

Small saucer or bottom of a plastic bottle

Wire

Saw (if necessary)

Screw half ring (hook).

1. Using screws, connect two small pieces of plywood. In this example, the dimensions of the plywood are 11 x 15 cm and 31 x 15 cm.

2. Using the bottle that you will later attach to the stand, mark the places where you will need to attach two pieces of wire - one at the neck, the other at the bottom of the bottle.

3. The neck of the bottle should be approximately 3-4 cm above the base.

4. Drill holes for the wire, insert your wire through the bottom, wrap it around the bottle and secure it to the back of the plywood (you can twist the wire or secure it with a stapler).

5. Fill the bottle with seeds, screw the lid on so as not to spill the seeds, turn it over and insert the bottle between the wires, place a saucer under it and remove the lid.

6. Screw a half-ring screw into the top of the plywood to hang the feeder.

Original DIY bird feeder

You will need:

Tin can (preferably with a lid)

Sisal rope (sisal rope) or thick rope

A piece of thin plywood, a branch, or any small metal piece

Hot glue.

1. If you have a jar with a lid, then the lid needs to be bent in half.

2. Take a small branch, piece of plywood, or other small piece that birds can perch on and glue it to the can.

3. Insert the bent lid as shown in the image (slightly inside the jar and over the metal part) and secure it with glue.

4. Take a thick rope or rope about 80 cm long and start wrapping the can so that the long ends of this rope (30 cm) remain at the beginning and at the end. Use glue to secure the rope to the can.

5. Cut the rope, tie the ends in a knot and secure with glue.

You will need:

3/4 cup birdseed

1/4 cup water

1 packet of gelatin

Twine or strong thread

Cookie pans

Baking paper.

1. Mix gelatin with water (1/4 cup) and bring to a boil, stirring. Make sure the gelatin is completely dissolved.

2. Remove from heat and let cool.

3. Add 3/4 cup birdseed. You can add more if it fits.

4. Place the cookie cutters on baking paper and fill them with the resulting food mixture.

5. Cut a piece of thread and tie its ends into a knot. Partially insert the thread into the mixture.

6. Leave the mixture to dry overnight, trying to turn it periodically when you have time.

7. Remove the molds and hang the food on the tree.

How to make your own bird feeder using tin cans

You will need:

3 cans of paint or cans

A piece of branch or wooden stick

Hot glue

Paints (if desired).

You can paint the jars, or you can leave them as is.

1. Glue a piece of branch to a jar for the birds to land and eat.

2. Wrap strong thread or ribbon around the jar and tie the ends in a knot. You can secure the tape with glue so that it sticks better to the jar.

3. Fill the jars with food and you're done!

How to make a bird feeder from a plastic bottle

Birds living in the wild need protection and care. It is especially difficult for them during winter: when it is frosty outside, it is so difficult to find shelter and food.

That is why caring people try to feed our younger “brothers” as much as possible. One of the ways that will not only help birds, but also decorate your garden is a feeder made from scrap materials.

In this article we have collected several of the most affordable options - based on descriptions and photographs, using already unnecessary items (plastic bottles or old dishes), you can easily arrange a place where flocks of birds will gather.

Material selection

After assessing the resources you have to create a feeder, you can choose an idea you like. However, it is worth remembering that not only its appearance, but also practical characteristics such as stability depend on the configuration.

That is why a good feeder must meet the following requirements:

Wear resistance and durability. Preference should be given to wood or plastic, which can withstand weather conditions without getting wet from rain and snow, or collapsing under gusts of wind.

In addition, the birds themselves often cause damage to the feeder - in search of crumbs, their beaks and claws scratch and tear fragile materials.

Proper size. Remember that if you cut out a small feeder, for example, from tetrapack, then large birds will not be able to eat from it, and small ones will start fights for space and shake out the food on the ground.

No sharp edges, protruding nails, etc. Birds are very delicate creatures, their feather protection and the skin on their legs cannot prevent cuts from sharp objects, so make sure that your feeder is not dangerous for them, especially if it is made of glass, plastic or planks!

Location and installation

Choosing the right location is extremely important!

Having chosen the most suitable position from the point of view of landscape design, evaluate:

Accessibility for birds. Perhaps the feeder will be closed from them by thick branches, or, conversely, it will be too open, and then, in a strong wind, the birds simply will not be able to get close to it.

Difficulty for cats. These animals are excellent hunters, especially those who live in villages and holiday villages. They are stronger, faster and more dexterous than their domestic counterparts, and therefore, sneaking up to the feeder, they can cause great damage to the bird community.

Ideas for making your own feeder

There are a huge number of different types of feeders - it all depends on your imagination and available materials.

We will try to consider both the simplest and the most original ideas.

House made of wood or plywood

Despite the apparent complexity, such a structure can be assembled with unnecessary boards, pieces of wood, glazing beads, plywood and, of course, special glue or nails.

Note!

The base should be a heavy, flat board. To make the walls and roof, you may need a drawing, however, you can get by with an eye.

A wooden bird feeder, depending on how much attention you pay to it, can become not only a place for birds to feed, but also an elegant decoration for your garden.

Feeder made from plastic bottles

This type of feeder is very easy to make and is perfect if you decide to involve children in the creation process. You need to cut one or two holes in the bottle so that you can not only pour in the food, but also access it without difficulty.

Of course, you should try to ensure that the cut edges come out neat and not too sharp (in addition, it is advisable to cover them with tape).

If you are using a small bottle (1.5-2 liters), then you can do it in two ways: cut a square or rectangular hole in the bottle, or prefer a U-shape so that you can bend a piece of plastic and make a visor.

If you decide to use a large bottle (5-6 liters, in which drinking water is usually sold), you can make a large side cutout. This will not only provide more food, but also give the birds room to maneuver.

Note!

To prevent the wind from ruffling a light bottle, it is worth placing a stone or a piece of brick at the bottom. This also applies to the next type of feeder.

Bird feeder made of tetra pack

You can also use juice or wine boxes to make a bird feeder.

To do this, you should follow the same technology as in the previous case: mark the location of the cut, cut it in shape, glue tape (or adhesive tape) along the bottom side of the opening, then make holes for a strong rope in the upper part of the tetra pack. All that remains is to hang the feeder in the place you choose.

Shoe box feeder

The cardboard from which the shoebox is made cannot be considered a durable material, but it is quite resistant to moisture, and if it is frosty outside, such a feeder can hang until spring.

The technology for making the feeder, as in previous cases, is also very simple: make four to six holes for the rope, slits on the sides and put a weight on the bottom for stability.

Note!

Other options

The above options are extremely popular - such feeders can be found at any dacha. If you want to make a unique feeder with your own hands, you should take unusual materials, for example, old tableware: a cup and saucer.

In the autumn, you can cut out a product from a pumpkin or zucchini; in the winter, halves of an orange, peeled from the pulp, are suitable for this. Such feeders will surprise your neighbors and will undoubtedly decorate the garden!

Photo of a DIY bird feeder

Sushi sticks are a universal material for crafts. You can make many useful things out of them. The main thing is to be careful and patient.

Before you start making a craft, make a sketch. Think about how you want it to look, draw the parts and make a drawing of their fastenings.

If you want sushi sticks, it's best not to attach them with regular glue. Yes, super glue will not help you make a good craft, since even the calmest person will not have the patience to hold the fragments tightly for several seconds so that they stick together. As a result, there will only be dirty hands and smeared and damaged parts. Use hot glue, small nails or a special stapler.

Fruit saucer made from sushi sticks: what you need

If you love Asian food and put together a craft, it will cost you almost nothing (provided you have the tools, of course). There are many options for what you can make from sushi sticks. The crafts turn out beautiful and original.

Materials and tools:

• wooden circle with a circumference of 30 cm in length;
• 30 sticks;
• nails, wood glue or hot glue;
• measuring meter;
• pencil;
• hammer;
• sandpaper.

Buy a wooden circle from a hardware store. If you live in a private sector or have friends from a rural area, ask them to cut a circle from a thick tree branch. Sand it with sandpaper so that it is even and smooth and does not leave splinters on your hands.

Fruit saucer made from sushi sticks: creation process

Now take some nails and a hammer. Attach the sticks in a circle. It is better to pre-calculate the interval between them. It is better to develop crafts using sushi sticks in advance on paper.

Measure the circumference and width of the sticks, divide the first by the second. For example, if the circumference is 25 cm, and you have 30 sticks 0.5 cm wide, then the interval will be about 3 mm, that is (25 cm - 30 * 0.5 cm): 30 cm.

To make it easier to mark the location, use a meter, which is used when sewing.

tools and materials

It's easy to make crafts from sushi sticks with your own hands. Each of us made bird feeders as children, cutting them out of bottles or juice or milk boxes. What if you try to do something more complicated?

Materials:

• 3 soda cans or copper sheets (you can buy these at a hardware store);
• 7 sticks;
• metal scissors;
• pencil and ruler;
• drill and drill bits;
• pushpins and nails;
• pliers.

Bird feeder: how to make

Use tin snips to remove the necks and bases of three cans (if you are using them).

Make a cut along each side to create 3 flat rectangular sheets. Each should measure approximately 217 x 88mm.

You need to flatten one sheet. Drill four holes the same diameter as sticks so you can stick them through. Cut two strips and make holes in them too.

Wrap the edges of the tin sheet tightly around two sticks. Trim anything that sticks out if it bothers you. Crafts made from sushi sticks are usually neat if the craftsman has skillful hands. But if the sticks stick out crookedly, it is better to cut them off.

Take one of the remaining sheets and cut out two rectangles measuring 127mm x 39mm.

Fold each rectangle twice, folding 13mm in on each side to form a long, thin strip.

Drill holes through the ends of each strip about the diameter of a stick. Insert the strips at the ends in the same way as you did for the roof.

Let's start creating the bottom of the feeder. Take the last sheet and make a smooth rectangle out of it. Cut out of tin, like paper, a box with low walls. Mark the cut locations on the edges. When you run scissors over them, the boots can be bent so that you get a box. Then it is better to run hot glue or PVA along the edges, or bend them so that the birds do not get hurt when they feast on the treat.

Bend the corners with pliers to prevent the box from opening, or fasten it with a stapler. An ordinary stapler can pierce a tin can - it is not very thick.

Drill holes in the walls so that a pushpin can be inserted through them.

When you made the strips for the roof frame you should have had some tin left over, use that to make fastenings for another stick for the birds to land on.

Household use

Crafts made from bamboo sushi sticks will decorate your home. In addition, sticks can be useful in everyday life. Neatly planed or unplaned, they will not spoil your interior.

Not enough skewers for your BBQ? Soak the chopsticks in water for 15 minutes and then use them to pierce meat and vegetables before placing them on the grill.

Prop the plants. It is convenient to stick them into the ground and tie the trunks of small plants to them. Insert sushi sticks into the soil near the spindly seedlings to give them the support they need.

If the hole into which the screw is screwed is too wide, sushi chopsticks will be very helpful. Insert it into the hole and fill the remaining space with glue. When everything is dry, trim off the excess. Now you can drill a hole in this place again.

Sticks are convenient to use for mixing paint. Regular gouache in a small jar or paint for walls or floors. Crafts from Chinese sushi sticks are not the only way to use waste.

Cleaning hard-to-reach places? Wrap the stick in a napkin or rag and push it into areas that were difficult to reach to remove dust and dirt buildup. They are also convenient for washing bottles. Stick the stick into the sponge and you have a convenient tool for cleaning hard-to-reach places.

Sushi sticks are useful for marking plants. Make a flag with the name of the flower and briefly describe how to care for it. It is very comfortable. Or write it directly on a stick.

As you can see, you can make a lot of things out of sushi sticks. Crafts are a great option, but they are by no means the only option.